ChamSys MagicQ Manuel d'utilisateur Page 45
- Page / 139
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ChamSys Ltd www.chamsys.co.uk
MagicQ User Manual 45 Version 1.3.0.0
6.15 Copy between heads
You can copy between heads using the keypad. To copy the head data, select some heads from the
keypad, press COPY and then enter the destination heads. For example, to copy from heads 1 to 2 to
heads 5 to 8
1 THRU 2 COPY 5 THRU 8 ENTER
Selected attributes can be copied rather than the entire head, by using SHIFT + COPY instead of COPY
and setting the attribute mask.
It is not necessary to have the same number of source heads as destination heads. Each of the source
heads is used in turn to copy data to the destination heads.
6.16 Head Macros
The console loads macros for the head from the personality file. Typical macros are "Lamp On",
"Lamp Off" and "Reset" - however they are very head dependent.
The "Lamp On", “Lamp Off” and “Reset” macros can be run at any time by using the following short-
cuts:
SHIFT + LOCATE Lamp on selected heads
CTRL + LOCATE Reset selected heads
CTRL + SHIFT + LOCATE Lamp off selected heads
Other head macros can be accessed in the Macro Window - press the HEAD MACRO soft button. A list
of the available macros is displayed. Select the macro you wish to run. Progress of the macro is shown
in the Status Window.
It is also possible to lamp on or off all fixtures from the MACRO window.
6.17 Selecting individual Heads
When programming it is often useful to be able to control one head out of a group of heads - for
instance, in order to set up it's position on the stage. Alternatively you may wish to apply an effect
to all the heads, such as fanning the position.
The head control buttons situated to the right of the touch screen enable the individual head to be
selected quickly. Once a number of heads have been selected for programming, the head control
buttons controls how changes are applied to those heads. By default changes are applied to all the
selected heads.
6.17.1 Locate
Pressing LOCATE, locates all the selected heads. The personality data for each head specifies what
happens to a head when it is located. Typically the shutter is opened, the dimmer is set to 100% and
pan and tilt are set to the centre position.
Pressing SHIFT LOCATE applies the lamp on macro to heads which have a lamp on functionality.
- MagicQ User Manual 1
- ChamSys Ltd 2
- TABLE OF CONTENTS 3
- 1 Introduction 10
- 2 Console Concepts 12
- 2.3 Cues 13
- 2.4 Cue Stacks 13
- 2.5 Playbacks 14
- 2.6 Pages 14
- 2.8 Window layouts 15
- 2.9 Shift Functions 15
- 2.10 The Programmer 15
- 2.11 Help 15
- 3 Quick Start 16
- 3.7 Selecting Heads 17
- 3.8 Recording a Group 18
- 3.9 Naming a Group 18
- 3.10 Recalling a Group 18
- 3.11 Locating Heads 18
- 3.12 Modifying Attributes 19
- 3.13 Recording a Palette 19
- 3.14 Adding in FX 20
- 3.15 Recording a Cue 20
- 3.17 Playing back your show 21
- 4 Console Layout 22
- 4.2 Playback Area 23
- 4.3 Head Control Area 24
- 4.4 Editor Area 24
- 4.5 Windows Select Area 25
- Common Actions 27
- 4.9 Moving items 28
- 4.10 Copying items 28
- 4.11 Removing items 28
- 4.12 Recording items 29
- 4.13 Actions on Playbacks 29
- 5 Patching 30
- 5.5 Head names and numbers 31
- 5.6 Gel name and number 32
- 5.7 Generating auto groups 32
- 5.8 Inverting and Swapping 32
- 5.10 Dimmer curves 33
- 5.14 Morphing heads 34
- 5.15 Importing heads 34
- 5.16 Exporting heads 35
- 5.18 Merging with DMX input 35
- 6 Setting Dimmer levels 37
- 6.4 Using Selected Heads 38
- 6.8 Selecting Heads 41
- 6.9 Using Groups 41
- 6.12 Locating Heads 43
- 6.13 Modifying Attributes 43
- 6.14 Flip 44
- 6.15 Copy between heads 45
- 6.16 Head Macros 45
- 6.18 Adding in FX 47
- 7 Palettes 51
- 7.3 Naming Palettes 52
- 7.4 Updating Palettes 52
- 8 Programmer 56
- 8.4 Recording a Cue 57
- 8.5 Record Options 58
- 8.6 Removing channels 59
- 8.7 Blind programming 59
- 8.9 Editing Cues 60
- 8.12 Snapshot 60
- 9 Cue Stacks 61
- 9.3 Cue Timing 62
- 9.4 Tracking 63
- 9.7 Copying and Moving Cues 65
- 10 Playback 66
- 10.1 Playback Display 67
- 10.3 Fader control 67
- 10.4 Playback Buttons 68
- 10.5 Playbacks Window 70
- 10.7 Default Cue Stacks 72
- 10.8 Group Masters 72
- 10.6 Wing Playbacks Pages 72
- 10.9 Playback Stomping 73
- 10.10 Playback priority 73
- 11.2 Over-ride / take-over 74
- 11.5 Modifying FX parameters 75
- 11.9 Adding in new FX 76
- 11.12 Busking Master 77
- 12 System Management 78
- 12.5 Loading Shows 79
- 12.6 Erasing 79
- 12.9 File Manager 80
- 12.11 Status Window 81
- 12.12 Editing Heads 81
- 12.13 Backup Archives 81
- 13 Settings 83
- 13.3 Wing Settings 84
- 13.4 Security settings 85
- 13.5 Programming settings 86
- 13.6 Playback Settings 89
- 13.7 General Settings 90
- 13.8 Cue Storage Settings 91
- 13.9 Interface Settings 91
- 13.10 Port Settings 92
- 13.12 Hardware Settings 93
- 13.16 LED brightness 95
- 13.17 Locking the console 95
- 13.18 Button test mode 95
- 14 Advanced Programming 97
- 14.4 HTP handling 98
- 14.5 LTP handling 99
- 14.6 Creating rig plans 99
- 14.7 Time-code support 100
- 14.8 Scheduled Events 100
- 15 MagicQ Multi Windows 101
- 16 Head Editor 101
- 16.1 General View 102
- 16.2 Channels View 103
- 16.3 Ranges View 104
- 16.4 Palettes View 105
- 16.5 Macros View 106
- 17.1 Patching LED on MagicQ 106
- 17.5 Using bitmaps 108
- 17.6 Using text strings 109
- 18 External Interfaces 111
- 18.3 Remote trigger input 114
- 19 Using Multiple Consoles 116
- 20 Execute Window 118
- 21 Media Servers 120
- 21.3 Live previews 121
- 21.4 Media layer selection 121
- 22 The MagicQ At A Glance 123
- 23 Troubleshooting 124
- 24 Button Functions 125
- 25 Licensing 136
- 26 Glossary 137
© 2020, manymanuals.fr. Tous droits réservés | 3.388 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels